Executive Summary

This technical document provides comprehensive engineering guidance for lb-10w oil-immersed ct: installation and maintenance specifications. The analysis covers operational mechanisms, design characteristics, implementation requirements, and compliance with international standards including IEC 61869 and IEEE C57 series.

Document Scope: This guide addresses technical professionals involved in specification, installation, commissioning, and maintenance of medium voltage instrument transformers and protection equipment in 6-35kV power distribution systems.

Key Topics Covered:

• Operating principles and mechanism analysis
• Design features and performance characteristics
• Engineering implementation checklist
• Standards compliance and testing requirements

Mechanism Analysis

Operating Principle

The equipment operates based on fundamental electromagnetic induction principles as defined in IEC 61869. Primary current or voltage is transformed to standardized secondary values suitable for metering, protection, and control applications.

Core Components

• Primary Circuit: High voltage/current input terminals with appropriate insulation coordination
• Magnetic Core: High-permeability silicon steel or nanocrystalline alloy for optimal accuracy
• Secondary Windings: Multiple accuracy classes available for simultaneous metering and protection
• Insulation System: Epoxy resin cast, oil-immersed, or SF6 gas insulation per application requirements
• Housing: Weather-resistant enclosure with IP65 or higher protection rating

Performance Characteristics

Error Mechanisms

Understanding potential error sources is critical for proper application:

1. Ratio Error: Deviation from nominal transformation ratio due to core magnetization characteristics
2. Phase Displacement: Angular difference between primary and secondary phasors
3. Burden Impact: Secondary load exceeding rated burden causes accuracy degradation
4. Saturation: Core saturation during fault conditions affects protection performance
5. Temperature Effects: Thermal variation influences magnetic properties and accuracy

Design Features

Insulation Technology

The equipment employs advanced insulation systems designed for long-term reliability in medium voltage applications:

• Epoxy Resin Casting: Vacuum pressure impregnation (VPI) ensures void-free insulation with excellent partial discharge performance (<10 pC at 1.2 Ur)
• Creepage Distance: Optimized for pollution degree III per IEC 60815
• Partial Discharge Inception: >1.2 × rated voltage for class A insulation systems

Magnetic Core Design

• Core Material: Grain-oriented silicon steel (CRGO) or nanocrystalline alloy for superior permeability
• Core Configuration: Toroidal or rectangular geometry optimized for flux distribution
• Flux Density: Operating point selected to balance accuracy and saturation margin

Secondary Terminal Configuration

• Terminal Types: Screw-type or spring-loaded terminals for 2.5-6 mm² conductors
• Polarity Marking: Clear P1/P2 (primary) and S1/S2 (secondary) identification per IEC 61869
• Multi-Ratio Taps: Available on selected models for flexible application
• Terminal Box: IP65 rated with adequate space for field wiring

Mechanical Construction

• Housing Material: Stainless steel (304/316), aluminum alloy, or UV-stable polymer
• Mounting: Flexible options including busbar mount, cable hang, or bracket installation
• Window Aperture: Sized to accommodate standard conductor and busbar dimensions
• Weight Optimization: Minimized mass reduces structural support requirements

Environmental Protection

• Ingress Protection: IP65 minimum for outdoor applications
• Corrosion Resistance: C5-M marine environment rating per ISO 12944
• UV Stability: Polymer components rated for 20+ years outdoor exposure
• Temperature Range: -25°C to +55°C ambient operation

Engineering Checklist

Pre-Installation Verification

• [ ] System Voltage: Verify equipment rating matches system nominal voltage (6/10/15/20/35 kV)
• [ ] Primary Current: Select ratio with 20-30% margin above maximum load current
• [ ] Accuracy Class: Confirm metering (0.2S/0.5S) and protection (5P10/5P20) requirements
• [ ] Burden Calculation: Sum all connected devices plus cable losses; verify ≤ rated burden
• [ ] Short-Circuit Rating: Ensure Ith and Idyn exceed system fault levels
• [ ] Physical Dimensions: Verify clearance requirements and mounting compatibility
• [ ] Environmental Conditions: Confirm altitude, temperature, and pollution degree compatibility

Installation Requirements

• [ ] Mounting Orientation: Install per manufacturer specifications (vertical/horizontal as designed)
• [ ] Conductor Alignment: Center primary conductor in aperture; avoid eccentric positioning
• [ ] Clearance Distances: Maintain minimum phase-to-phase and phase-to-ground clearances per IEC 61869
• [ ] Grounding: Connect equipment ground terminal to substation ground grid
• [ ] Secondary Wiring: Use minimum 2.5 mm² copper; keep secondary cable length <50m where possible
• [ ] Polarity: Verify P1/P2 and S1/S2 orientation matches protection scheme requirements
• [ ] Terminal Tightness: Torque all connections to manufacturer specifications

Commissioning Tests

• [ ] Visual Inspection: Check for physical damage, proper labeling, and secure mounting
• [ ] Insulation Resistance: Megger test primary-to-ground and secondary-to-ground (>1000 MΩ at 2500V DC)
• [ ] Ratio Test: Verify transformation ratio at multiple tap points (if applicable)
• [ ] Polarity Test: Confirm additive/subtractive polarity per connection diagram
• [ ] Excitation Test: Measure magnetizing current at rated voltage (compare to factory data)
• [ ] Burden Verification: Measure actual secondary circuit impedance
• [ ] Winding Resistance: DC resistance measurement for baseline documentation

Periodic Maintenance

• [ ] Annual Visual: Inspect for contamination, damage, or abnormal heating
• [ ] 3-Year Testing: Insulation resistance, ratio verification, polarity check
• [ ] 5-Year Comprehensive: Full testing per IEC 61869 including accuracy verification
• [ ] Post-Fault Inspection: Examine after any through-fault exceeding rated Ith
• [ ] Terminal Inspection: Check tightness and corrosion annually

Safety Precautions

• [ ] Short-circuit secondary terminals before disconnecting any secondary wiring
• [ ] Use properly rated shorting blocks or test switches
• [ ] Verify secondary circuit continuity before removing shorting devices
• [ ] Follow lockout/tagout procedures for all maintenance activities
• [ ] Wear appropriate PPE for working on energized equipment

Standards Reference

International Standards

IEEE Standards

Chinese National Standards (GB)

Testing Standards

Compliance Documentation

Manufacturers should provide the following documentation with each unit:

• Type Test Certificate: Demonstrates compliance with applicable standards
• Routine Test Report: Documents results of mandatory production tests
• Accuracy Certificate: Verifies ratio and phase angle accuracy at rated burden
• Dimensional Drawing: Shows physical dimensions and mounting details
• Connection Diagram: Illustrates terminal identification and wiring
• Installation Manual: Provides step-by-step installation instructions
• Maintenance Guide: Outlines periodic maintenance requirements

Document Version: 1.0 | Generated: 2026-03-02 | Classification: Technical Reference

Standards Compliance: IEC 61869 Series, IEEE C57.13 Series, GB 20840 Series

LJ-2,4,7,LJ1 Zero-sequence current transformer for Grounding Protection

JLSZY-35Kv high-voltate Outdoor Epoxy Resin Casting Combined Transformer

JDG4-0.5 Indoor Low Voltage Transformer, dry-type transformer

JSJW-6, JSJW-10kv Three-Phase Oil-Immersed Voltage Transformers

• Instrument Transformer Fault Handling: A Technical Guide
• Zero-Sequence Current Transformers vs. Standard Current Transformers: Installation Gap Sensitivity Analysis
• Common Faults and Troubleshooting of Current Transformers Faults
• Ground Fault Protection Coordination in Ungrounded Systems
• Error Analysis and Maintenance of Current Transformers in Power Systems
• Ferroresonance Overvoltage Protection in 3-35kV Voltage Transformers: Mechanism Analysis and Mitigation Strategies